From R&R, a company that knows fixturing!

If we make your job easier then we have done our job. We strive to have the best available products through innovation and reduced cost.

Here are our newest offerings:

---

adjustable slide acylic extension

Screw any component onto the acylic slide to extend the reach of the component.

Part #: ASAE-4

Thread: M4

Price: $85

---

adjustable steel jack stand

To allow variable heights of up to 22mm and then lock into position for large or heavy parts.

Part #: AJS-35-8

Thread: M8

Price: $85

---

adjustable slide

To place components in between holes on a CMM or vision plate.

Part #: ASA-2-20 (acrylic), AS-45-8, ASA-45-4 (acrylic)

Thread: 1/4-20, M8, M4

Price: $33.50, $30, $30

---

delrin resting pins

To rest a part on a non-marring point.

Part #: RPD-20, RPD-4

Thread: 1/4-20, M4

Price: $15, $16

---

delrin standoffs

To elevate and locate a part using a non-marring material.

Part #: SD-251-20,SD-3751-20, SD-501-20, SD-751-20, SD-11-20, SD-610-4,SD-910-4, SD-1210-4

Thread: 1/4-20, M4

Price: $13.50 - $17.25

---

delrin pin standoffs

To elevate and locate a part against a pin using a non-marring material.

Part #: SPD-37550-20,SPD-501-20,SPD-751-20,SPD-610-4,SPD-910-4,SPD-1210-4

Thread: 1/4-20, M4

Price: $14.00 - $17.25

---

steel cone

To rest a part on a rounded point.

Part #: RCS-25-8

Thread: M8

Price: $28.50

spring pusher standoff clamp

Designed for fixturing small parts in tight or compact space. Ideal for positioning parts and for profile clamping with maintaining constant pressure on part, minimizing fixturing space.

Part #: CSPS-1210-4, CSPS-751-20

Thread: M4, 1/4-20

Price: $45, $50

micro vise clamp

Ideal for holding parts horizontally or vertically with
minimum contact on the part made with a V notch in
both directions for holding cylindrical and tubular parts
as well. Micro vise clamp sold with or without base.

Part #: CVM-4, CVM-20, CVM-B-4, CVM-B-20

Thread: M4, 1/4-20

Price: $115, w/ base $145

micro center

Has adjustability to hold cylindrical parts up to 26mm in length and 25mm dia. (or smaller) using a female or male tapered pin. You can gain access around the part for touch probing with your CMM or viewing with your vision system.

Part #: CMC-4

Thread: M4

Price: $145

micro adjustable V

For cylindrical parts smaller than 6.5mm dia., you can hold them within the V, varying the adjustment length of the part. Parts can be held down with optional clamp, if needed.

Part #: AVM-4

Thread: M4

Price: $130

rotating 3-jaw clamp

For clamping parts on ID and OD, the rotating 3-jaw clamp can be locked into position on the part then rotated to a marked increment to help locate the rotation of the part for measurement. The rotating 3-jaw clamp can accommodate 7/8” dia. up to 3-1/8” dia.

Part #: CJR-3-4

Thread: M4

Price: $285

large adjustable pivot clamp

Used to hold parts vertically or horizontally with 4-axis rotation. Especially good for clamping sheetmetal and plastic parts up.

Part #: CAP-2-20, CAP-50-8

Thread: 1/4-20, M8

Price: $350